ANTIFUSE PROGRAMMING TECHNOLOGY PDF

An Antifuse programming technology is predominantly associated with _____. Antifuse technology is nonvolatile, so it is live at power-up and programming services, either from Actel or from other vendors, are also used. recommended programming practices for antifuse devices. For SoC Antifuse technology is nonvolatile, so it is live at power-up and inherently very secure.

Author: Akinogul Kegar
Country: Italy
Language: English (Spanish)
Genre: Relationship
Published (Last): 14 November 2010
Pages: 268
PDF File Size: 5.47 Mb
ePub File Size: 11.21 Mb
ISBN: 382-1-30715-367-9
Downloads: 18263
Price: Free* [*Free Regsitration Required]
Uploader: Dajora

Articles needing additional references from May All articles needing additional references. Also circuits built via the antifuse’s permanent conductive paths may be faster than similar circuits implemented in PLDs using SRAM technology.

QuickLogic Corporation refers to their antifuses as “ViaLinks” because blown fuses create a connection between two crossing layers of wiring on the chip in the same way that progrramming via on a printed circuit board creates a connection between copper layers.

Antifuses may be used in programmable read-only memory PROM. A standard NPN transistor structure is often used in common bipolar processes as the antifuse. In this way, the failed lamp was bypassed and illumination restored to programminf rest of the street.

Antifuse programming technology – FPGAs

One approach for the ICs that use antifuse technology employs a thin barrier of non-conducting amorphous silicon between two metal conductors. The p-n junction that serves as such diode is overloaded with a current spike and overheated. Dielectric antifuses employ a very thin oxide barrier between a pair of conductors. In a similar fashion to that of Christmas tree lights, before the advent of high-intensity discharge lampsstreet light circuits using incandescent light bulbs were often operated as high-voltage series circuits.

  LEI 11705 ATUALIZADA PDF

They may be less susceptible to alpha particles which can cause circuits to malfunction. They are historically used especially with bipolar processes, where the thin oxide needed for dielectric antifuses is not available.

Antifuse – Wikipedia

As the number of bonding pads is limited for a given size of the chip, various texhnology strategies are used for larger number of antifuses. Zener diodes can be used as antifuses.

This rapidly causes the antifuse to short out the blown bulb, allowing the series circuit to resume functioning, albeit with a larger proportion of the mains voltage now applied to each of the remaining lamps. A specialized structure optimized for the purpose can be employed where the antifuse is an integral part of the design.

This article needs additional citations for verification. This page was last edited on 7 Julyat Unsourced material may be antlfuse and removed. The larger, traditional, C7 and C9 style lights are wired in parallel and are rated to operate directly at mains voltage.

Their disadvantage, however, is lower area efficiency compared to other types. Whereas a fuse starts with a low resistance and is designed progeamming permanently break an electrically conductive path typically when the current through the path exceeds a specified limitan antifuse starts with a high resistance and is designed to permanently create antifise electrically conductive path typically when the voltage across the antifuse exceeds a certain level.

The conductive shunt therefore does not compromise integrity and reliability of the semiconductor device. Zener zap is frequently employed in mixed-signal circuits for trimming values of analog components.

From Wikipedia, the free encyclopedia.

Antifuses are best known for their use in mini-light or miniature style low-voltage Christmas tree lights. Retrieved from ” https: The parallel resistors cannot have too low value as that would sink the zapping current; a series-parallel combination of resistors and antifuses is employed in such cases.

  ATTITUDES PERSONALITY AND BEHAVIOR BY ICEK AJZEN PDF

Antifuse programming technology – FPGAs

antifuxe Ordinarily for operation from mains voltagesthe lamps are wired in series. This programming, performed after manufacturing, is permanent and irreversible. The resulting resistance of the junction is in the range of 10 ohms. In some cases pgogramming combined circuit with zeners and transistors can be used to form a zapping matrix; with additional zeners, the trimming which uses voltages higher than the normal operational voltage of the chip can be performed even after packaging the chip.

FPGAs in computer

The antifuse is usually triggered using an approximately 5 mA current. May Learn how and when to remove this template message. The spike is formed on and slightly below the silicon surface, ahtifuse below the passivation layer without damaging it. Because the series string would be rendered inoperable by a single lamp failing, each bulb has an antifuse installed within it.

It is therefore necessary to shift the manufacturing tolerances so that the lowest-value typically made is equal to or larger than the desired value. Antifuses are widely used to permanently program integrated circuits ICs. The insulation of the antifuse wire withstands the ordinary low antifues imposed across a functioning lamp but rapidly breaks down under the full mains voltage, giving the antifuse action.

Please help improve this article by adding citations to reliable sources.