ABB ACS150 USER MANUAL PDF

ABB ACS Operation Limits. Setup the For settings of other parameters/ macros and detailed explanation hereof, see the instructions manual from ABB. View and Download ABB ACS user manual online. ACS Controller pdf manual download. The ABB ACS series component drives are easy to select and come with a variety of standard features acsuser-manual-partpdf.

Author: Voodookree Nikojinn
Country: Antigua & Barbuda
Language: English (Spanish)
Genre: Literature
Published (Last): 21 December 2006
Pages: 357
PDF File Size: 8.13 Mb
ePub File Size: 14.36 Mb
ISBN: 130-9-19390-771-6
Downloads: 57347
Price: Free* [*Free Regsitration Required]
Uploader: Kazigal

Page 24 Motor cable shield To function as a protective conductor, the shield must have the same cross-sectional area as the phase conductors when they are made of the same metal. For the parameter default mqnual, see section Default values with different macros on page Enter text from picture: Ignoring the safety instructions can cause injury or death. Check that there are no faults or alarms shown in the display.

Ratings on page Plan the installation: Output mode In the Output mode, you can: The ACS includes an integrated potentiometer located at the front of the drive.

Installation Checklist Installation checklist Checklist Check the mechanical ueer electrical installation of the drive before start-up. How to reset The drive can be reset either by pressing the keypad key on the control panel, through digital input, or by manuao the supply voltage off for a while.

Stop drive and change parameter value. How to start, stop and switch between local and remote control You can start, stop and switch between local and remote control in any mode.

  8320G174 ASCO PDF

To prevent dependent overheating, set IR compensation voltage as low as possible. Parameters which are hidden by the FlashDrop device are not visible.

Industrial Component Drives ACS | Variable Speed AC Motor Drive (ABB) | ECD Controls

During the delay the drive knows accurately the rotor position. Electrical equipment of machines. Page 28 Planning electrical installation Use LCD display — Divided into five areas: A Value is at or above maximum limit.

Mounting the drive Mount the drive Note: The chapter describes the control panel keys and display fields. Determine the required maximum braking power P for the application. Press key to switch In remote control, the panel display shows text REM. Page 16 Hardware description Make sure that dust from drilling does not enter the drive during the No free space is required on the sides of the drive, so they can be mounted side by side.

The ACS has five application macros.

For ACSx drives, other measures for protection in case of direct or indirect contact, such as separation from the environment by double or reinforced insulation or isolation from the supply system by a transformer, can also be applied. Short Parameter mode and Long Parameter mode. Control Panel The chapter describes the control panel keys and display fields. Amendment A1 Provisions for compliance: Ensure that the drive is in remote control. Supervision mnaual can be monitored with relay output.

Page 62 Abn macros Motor Potentiometer macro This macro provides a cost-effective interface for PLCs that vary the speed of the drive using only digital signals.

About The Manual It contains a flowchart of steps for checking the delivery and installing and commissioning the drive. If value is set to 0, no signal is selected. Analog signal if connected: Page 50 Reference mode In the Reference mode, you can: Connect the conductors to the appropriate terminals. Installation checklist Checklist Check the mechanical and electrical installation of the drive before start-up. F used for drive internal temperature measurement is open or short-circuited.

  GARMIN 265WT MANUAL PDF

They must be removed and handled according to local regulations. You find the type code on the type designation label attached to the drive.

Page 45 The ACS includes an integrated potentiometer located at the front of the drive. The figure below illustrates the IR compensation. Overview The following table summarizes the key functions and displays on the Integrated Control Panel. The brake resistor is selected using the table and equations presented in this section.

Page 33 Procedure 1. Thermistor Contact your local ABB representative.

Industrial Component Drives ACS150

Without plates R0 and R1 Page Motor Ground the other end of the PE conductor at the distribution board. The requirements are easily met with a copper or aluminium shield. Page 23 – Selecting the power cables Page 24 Page 25 – Protecting the relay output contact and Current and power The current and power ratings are given below.

Free space around the drive The required free space for cooling above and below the drive is 75 mm 3 in.